Team:IISc-Bangalore/Results

  1. Chitosan
  2. Biotin-Streptavidin
  3. SpyCatcher-SpyTag
  4. Future Work
  5. Potential Applications

Chitosan

Chitosan

Four different concentrations of chitosan were added to gas vesicle suspensions (30 µl stock) and the resulting solutions were diluted to 2 mL to perform a flotation spectrophotometry assay.

Sample Label Effective gas vesicle concentration
(ng/μl)
Effective chitosan concentration
(ng/μl)
Remarks (Relative concentration)
1 15 0 Control tube (0)
2A 15 5 First replicate (0.1)
2B 15 5 Second replicate (0.1)
3A 15 50 First replicate (1)
3B 15 50 Second replicate (1)
4A 15 500 First replicate (10)
4B 15 500 Second replicate (10)
5A 15 5000 First replicate (100)
5B 15 5000 Second replicate (100)

Averaged over the replicates, the data shows a markedly-faster decrease in OD with time for chitosan-treated gas vesicles. The control gas vesicle suspensions (without chitosan) show no significant decrease in OD over a duration of two hours while the suspensions with intermediate chitosan concentrations show a fast decrease at the start which saturates as time passes. All other curves lie above this one (Fig 1).

Fig 1: Percent of initial OD500 as a function of time

At very high concentrations, the saturation point shifted upwards. We postulate that this is because of the irreversible denaturation of gas vesicles by the action of excess acetic acid during chitosan incubation. A more detailed analysis can be conducted to determine the optimum concentration at which maximum flotation is achieved. From these results, we expect it to this optimal concentration be around 500 ng/µl.

The plot was smoothed out over a window of 85 data points giving the smooth profiles. (Fig 2)

Fig 2: Percent of initial OD500 as a function of time (smoothed).

It was found that the particle size increased considerably on addition of chitosan. The data from the Dynamic Light Scattering experiment is plotted in Figure 3. Again, at very high chitosan concentrations, the RH dropped back to a nominal value, probably due to lysis of the vesicles during incubation with concentrated acetic acid.

Fig 3: Particle size trend with increasing chitosan concentration.

Biotin-Streptavidin

NHS-biotin was used to biotinylate gas vesicles and these biotinylated gas vesicles were incubated with streptavidin to allow aggregation. This experiment was conducted in two ways.

Method I:

Our protocol for biotinylation requires the addition of NHS-biotin in greater than or equal to a 20 fold molar excess. The first strategy that was adopted to discourage binding of streptavidin was to add the streptavidin in excess. As each streptavidin molecule can potentially bind to four biotins, a 1/4 molar ratio would imply proper stoichiometry for the reactions. We settled with a 1:2 and 1:1 ratio of streptavidin:biotin to ensure that all biotin in the suspension is sequestered.

Method II:

The second method we used to remove excess biotin was enrichment of the gas vesicles by centrifugation. After incubation with NHS-biotin, the gas vesicles were centrifuged at 500 rpm overnight to allow them to float to the top. This was followed by removal of the upper layer and incubation with quantities of streptavidin on the order of number of gas vesicles in the suspension. The measurements were repeated thrice for all samples.

Sample Label Effective gas vesicle concentration
(ng/µl)
Effective NHS-Biotin concentration
(ng/µl)
Effective Streptavidin concentration
(ng/µl)
Remarks
S2Ctrl 15 300 0 Control (no streptavidin)
SB 15 300 100 Method I
SC 15 300 200 Method I
S21 15 300 1 Method II
S23 15 300 3 Method II
S25 15 300 5 Method II

All the above experiments gave negative results, with the particle sizes for both the treated and untreated vesicles being similar to each other. This could mean either of these two possibilities:

  • NHS-Biotin was unable to biotinylate the GvpA amine residues, or
  • Our methods were unable to eliminate unnecessary free biotin-streptavidin interactions.

The first possibility eliminates the chance of using biotin-streptavidin for future experiments. No spectrophotometry assays were carried out with these solutions due to the absence of positive results from the DLS experiments. The following graph shows the particle sizes recorded at different concentrations of streptavidin.

Fig 4: Particle size trend with increasing streptavidin concentration.

SpyCatcher-SpyTag

We were able to express sfGFP-SpyCatcher fusion protein in BL21 (DE3) as our assembly for this part proceeded smoothly. However, since our mCherry-SpyTag assembly did not work, we were unable to continue with this part of our experiment. However, future teams may use our designed BioBricks to try out this experiment and verify with DLS and spectrophotometry assays.

Potential Applications

Bioremediation of oil spills

Floating gas vesicles can be used for bioremediation of oil spills: by expressing lipases on the surface of the gas vesicles, a floating oil-degrading mesh could be developed. This is a specific example of a more general application: gas functionalized gas vesicles can be used to create a bioactive mesh for various purposes; since multiple proteins can be tagged to the same gas vesicle, a whole host of enzymatic reactions can take place on the same gas vesicle based scaffold!

Flotation-based separation

Inspired by our visit to Lupin, this application involves expressing specific binding proteins to the surface of gas vesicles — antibodies against cell-surface receptors, for example — and adding them to the mixture from which those particular cells are to be purified. By adding chitosan at the correct concentrations, the gas vesicles can be aggregated, causing them to float up and carry the cells to be purified with them!