Difference between revisions of "Team:Arizona State/Notebook"

In preparation Alyssa and I rehydrated 2 backbones from iGEM, the PSB1C3 and PSB1A3. The C3 was from plate 7 location O,23 and the A3 was from plate 4 location H,2. Will let the plates grow overnight in the incubator and make MP samples, in triplicates of each, tomorrow.

DNA extraction from kit and rehydration protocol:

To use the DNA in the Distribution Kit, follow these instructions:

Note: There is an estimated 2-3ng of DNA in each well, following this protocol, assume that you are transforming with 200- 300pg/µL

With a pipette tip, punch a hole through the foil cover into the corresponding well of the part that you want. Make sure you have properly oriented the plate. Do not remove the foil cover, as it could lead to cross contamination between the wells
Pipette 10µL of dH2O (distilled water) into the well. Pipette up and down a few times and let sit for 5 minutes to make sure the dried DNA is fully resuspended. The resuspension will be red, as the dried DNA has cresol red dye. We recommend that you do not use TE to resuspend the dried DNA.
Transform 1µL of the resuspended DNA into your desired competent cells, plate your transformation with the appropriate antibiotic* and grow overnight.
Pick a single colony and inoculate broth (again, with the correct antibiotic) and grow for 16 hours
Use the resulting culture to miniprep the DNA AND make your own glycerol stock (for further instruction on making a glycerol see this page). We recommend using the miniprepped DNA to run QC tests, such as restriction digests and sequencing.

* To know which antibiotics to use, look at the plasmid that the part is in. The naming scheme for plasmids is specifically designed to indicate antibiotic resistance.

7/20/2017 - something went wrong with the process, the plates to not show sufficient growth. Tests and plating will be redone today.

@@ Line 23: / Line 23: @@
 <p> <b> 7/20/2017 - something went wrong with the process, the plates to not show sufficient growth. Tests and plating will be redone today. </b> </p>
 <center><img src="https://static.igem.org/mediawiki/2017/6/61/Image_asu.png"style="width:428px;height:428px;/> </center>
-<img src="https://static.igem.org/mediawiki/2017/3/3f/Image_%281%29.png"/>
 <p> Gathered the available colonies and put in LB with (AMP or CHLOR) to grow overnight and replate for more usable growth to be MP. samples in the shaking incu overnight, was able to grab 3 colonies from the A3 and two from the C3. Put everything in the shaking at 345pm </p>
-<img src="https://static.igem.org/mediawiki/2017/a/a6/Image_asu_2%281%29.png"style="width:428px;height:428px;/>
-<img src="https://static.igem.org/mediawiki/2017/6/6d/Image_%283%29.png"/>
 <p> Doing the MP on the A3 and C3 growth tubes. Concentrations: </p>
@@ Line 39: / Line 33: @@
   <p>psb1a3: 67ng/ul </p>
 <p>psb1a3: 75ng/ul </p>
-<img src="https://static.igem.org/mediawiki/2017/1/19/Image_%285%29.png"style="width:428px;height:428px;/>
@@ Line 48: / Line 40: @@
 <p>Since it is the weekend, instead of placing the new agar plate with the 24 samples of plated AUBr and BTA3 into the 37c incubator, leaving the sample out in room temperature as to not accelerate the growth too much over the weekend. See picture below: </p>
+</div>
 </html>