Protocols

Gibson

Gibson Assembly allows for successful assembly of multiple DNA fragments, regardless of fragment length or end compatibility. (1). The method was invented in 2009 by Daniel G. Gibson, of the J. Craig Venter Institute. The assembly reaction is carried out in one single reaction-tube, all at once, at 50° Celsius for 15-60 minutes. The process involves three different enzymatic actions. A 5’ exonuclease creates overhangs, enabling matched fragments to anneal. Then a DNA polymerase fills gap between the annealed strands and the 5´ end. Finally, a DNA ligase seals the gaps between the filled in gap and the annealed strands.


Protocol used for Gibson

Modifications
(Used for insertion of nmt1, cyc1, sfGFP and composite part into submition vector pSB1C3 and insertion of composite part into yeast vector) (i) Volume Changes:
    V_insert = x
    V_vector = y
    V_gibson = x+y
    V_water = 0µl

(ii) Incubation for 1h, not 15 min
(iii) Before transformation: One transformation with x ul concentrated Gibson solution and one transformation with Gibson solution diluted 1:3 and transformation with 3*x ul diluted Gibson solution.




Transformation

E.coli TOP10 (Used for nmt1, cyc1, sfGFP and composite part) : One Shot® TOP10 E. coli are provided at a transformation efficiency of 1 x 109 cfu/µg supercoiled DNA and are ideal for high-efficiency cloning and plasmid propagation. They allow stable replication of high-copy number plasmids.

Chemical Transformation Procedure

Modifications
In Step 5, Incubate for exactly 30-45 seconds in the 42°C water bath. Do not mix or shake. In Step 7, Add 200-250 µl of rom temperatured S.O.C medium to each vial. S.O.C is a rich medium; sterile technique must be practiced to avoid contamination

E.coli DH5Alpha (Used for the Interlab and for purification of sfGFP):
Protocol Modifications:
Step 15 and Step 16 not done




PCR

The goal of PCR is to amplify a section of DNA of interest for DNA analysis (e.g. gene insertion, sequencing, etc). The amplification rate is exponential.
• Tag polimerase (25µl reaction) Used for colony PCR for cyc1
Protocol Here
Specifications


10X Standard Taq Reaction Buffer	2.5 μl
10 mM dNTPs	0.5 µl
10 µM VF2	0.5 µl
10 µM VR	0.5 µl
Template DNA	variable
Taq DNA Polymerase	0.125 µl
Nuclease-free water to	25 µl

1) 95°C	30 sec
2) 95°C	30 sec
3) 63°C	1 min
4) 68°C	1 min/kb
5) 2/30X
6) 68°C	5 min
7) 10°C	forever




• Phusion polymerase (20µl reaction) Used for colony PCR for nmt1 and composite part :
Protocol Here
Specifications


15X Phusion HF or GC Buffer	4 µl
10 mM dNTPs	0.4 µl
10 µM VF2	1 µl
10 µM VR	1 µl
Template DNA	variable
Phusion DNA Polymerase	0.2 µl
Nuclease-free water to	20 µl

1) 95°C	30 sec
2) 98°C	30 sec
3) 63°C	1 min
4) 72°C	1 min/kb
5) 2/30X
6) 72°C	5 min
7) 10°C	forever




• 5 PRIME HotMasterMix (50µl and 10µl reaction) Used for colony PCR for nmt1 and composite part :
Protocol Here Specifications
10 µM VF2 0.4 µl 10 µM VR 0.4 µl Template DNA variable 5 PRIME HotMasterMix 4 µl Nuclease-free water 5.2 µl Cycles: 1) 94°C 2 min 2) 94°C 20 seconds 3) 55°C 30 seconds 4) 70°C 1 min/kb 5) 2/30X 6) 70°C 5 min 7) 10°C forever Primers for amplification of composite part: Fw: aaaaagaattcgcggccgcttc Rev: aaaaactgagcggccgctactag





Gel

For making a small 1% gel:
Weigh out 0.5 g of agarose and mix it with 50 ml of 1x TAE buffer in a 100 ml Erlenmeyer flask.
Dissolve the agarose by bringing the mixture to the boiling point in a microwave oven, followed by mixing (by swirling the flask). Repeat the heating and mixing until all the agarose has dissolved.
Cool the agarose solution to ~50 o C by leaving it on the bench for ~20 min (or you may accelerate the cooling by applying cold water from the tap to the outside of the flask).
Using gloves, add 5 l GelRed (10 000x). Swirl the flask gently to mix, try to avoid bubbles.
Pour the gel carefully into the mold. Bubbles may be removed/punctured by using a pipette tip.



Miniprep


Protocol
Modifications:

During the first attempt ethanol was not added to the PE buffer, which resulted in an unsuccessful miniprepl
In the second attempt 72/4% ethanol was added, as opposed to the recommended 96-100%, resulting in a successful miniprep

INTERLAB

96-Well Transformation Protocol:
Protocol
Plate reader protocol:
Protocol

References: