Team:SUSTech Shenzhen/Model1

Team SUSTC-Shenzhen

Model

Microfluidic

1. Microfluidic

In our project, we are required to insert a new gene into the Caenorhabditis elegans(C. elegans') genome and express the two channelrhodopsins in the olfactory receptor neuron pair. Because of the exogenous genes, we need to test if those exogenous genes will influence the olfactory receptor neuron pair. Therefore, we designed the Gaussian plate (Fig.1 a microfluidic chip.[1])

T--SUSTech Shenzhen--Microfuildics--gs.png
Fig.1 The Gaussian plate It is a microfluidic chip made by Polydimethylsiloxane (PDMS)

Using this chip we can know the C. elegans’ preference and repulsion through their distribution in the chip. This plate consists of two layers (Fig.1). We inject chemicals into the first layer to form a concentration gradient (Fig.2), then the chemicals with different concentration diffuse downward across the Polydimethylsiloxane (PDMS) and reach the second layer, so that the worms can sense the chemicals.


T--SUSTech Shenzhen--Microfuildics--cg.png
Fig.2 The concentration gradient of the chemicals. We inject the chemicals into the inlet 1 and the water into the inlet 2 to form it.

Therefore, we need to know the chemical diffusion in PDMS to get the time when the worms can sense the chemicals (Fig.3). In order to calculate the time, we used the diffusion model to help us.


T--SUSTech Shenzhen--Microfuildics--layer.png
Fig.3 A) The chemicals diffuse downward across the PDMS. B) The chemical can across the PDMS to enter in the M9 buffer. The M9 buffer is injected into the layer2 continually so the chemicals will not be accumulated in the M9 buffer, on the other words the concentration of layer2 is always equal to the concentration at the bottom of the PDMS.

1.1 Diffusion

For nonsteady-state diffusion, there is an equation named Fick’s second law[2]: \frac{\partial C}{\partial t}=D \frac{\partial^2 C}{\partial x^2}

The constant of proportionality D is called the diffusion coefficient, which is expressed in square meters per second. Concentration C is plotted versus position (or distance) within the solid x and the time t.

For t=0, C=C0 at 0≤x≤∞;

For t>0, C=Cs (the constant surface concentration) at x=0;

C=C0 at x=∞. And then there is a general solution: \frac{C_x-C_0}{C_s-C_0}=1-erf(\frac{x}{2 \sqrt{Dt}}) Where Cx represents the concentration at distance x after time t.

\frac{x}{2 \sqrt{Dt}}=constant, so if this constant can be calculated, the equation of distance x and time t can also be gotten.

In our model, C0=0, so the equation is changed to \frac{C_x}{C_s}=1-erf(\frac{x}{2 \sqrt{Dt}}) Cx represents the concentration at distance x that C. elegans can feel. We set that the Cx = 1uM (for diacetyl) ,the optimum concentration can be sensed by the C. elegans.

Cs is the concentration set by our own and it is a constant. We set that the Cs = 288uM (for diacetyl), x is 5mm

According to the equation we can get that the erf (\frac{x}{2 \sqrt{Dt}})=0.9965 and then referred to the Table 1.1 we can get that the \frac{x}{2 \sqrt{Dt}}=2.2, and D is the diffusion coefficient for 2-nonanone or diacetyl in PDMS. We need to calculate the D to get the time t according to the equation. We used the force-field method to get the D of those two chemicals (the concrete operational process is shown in 1.3).

D(2-nonanone) = 6.78*10-6cm2/s

D(diacetyl) = 6.78*10-6cm2/s

Finally, we can get the time t = 12 mins, on the other words, we cannot inject the C. elegans until the chemicals are injecting for 12 mins in layer 1(for diacetyl).


T--SUSTech Shenzhen--Microfuildics--table.png

1.2 The Calculation of Diffusion Coefficient(D)

The diffusivity of a gas in an organic solvent, polymer, or zeolite can be calculated by running a molecular dynamics simulation and determining the mean square displacement of the gas in the material. This allows us to calculate the self-diffusivity coefficient of the gas and gives an insight into the overall diffusivity. As we are performing a molecular dynamics calculation, we can analyze the effect of temperature, pressure, density, and penetrant size and structure on diffusion. We used force-field method to calculate the D in PDMS by Material Studio (MS) a software for material calculation.[3][4]

1.2.1 Set up the initial structures

First, we set up the initial structure of the PDMS and the chemicals (Fig.4 and Fig.5).


T--SUSTech Shenzhen--Microfuildics1-Model.png
Fig.4 The structure of PDMS
T--SUSTech Shenzhen--Microfuildics2-Model.png
Fig.5 The structure of diacetyl

1.2.2 Build an amorphous cell

Then, we put the two molecules in to an amorphous cell (Fig.6).

T--SUSTech Shenzhen--Microfuildics3-Model.png
Fig.6 The amorphous cell

1.2.3 Relax the cell

When we generate an amorphous cell, the molecules may not be equally distributed throughout the cell, creating areas of vacuum. To correct this, we must perform a short energy minimization to optimize the cell. After the minimization, we should run a short molecular dynamics simulation to equilibrate the cell.

T--SUSTech Shenzhen--Microfuildics4-Model.png
Fig.7 The cell after relaxing

1.2.4 Run and analyze molecular dynamics

1.2.5 Export data and calculate the diffusivity

Then we can got the D of 2-nonanone and diacetyl:

D(2-nonanone) = 6.78*10-6cm2/s

D(diacetyl) = 6.78*10-6cm2/s


T--SUSTech Shenzhen--Microfuildics5-Model.png
Fig.8 The diffusion coefficient of 2-nonanone in PDMS

T--SUSTech Shenzhen--Microfuildics6-Model.png
Fig.9 The diffusion coefficient of diacetyl in PDMS

References

  1. ↑ Albrecht, D. R. and C. I. Bargmann (2011). “High-content behavioral analysis of Caenorhabditis elegans in precise spatiotemporal chemical environments.” Nature Methods 8(7): 599-605.
  2. ↑ Callister, W. D., & Rethwisch, D. G. (2004). Fundamentals of Materials Science and Engineering. John Wiley and Sons Ltd.
  3. ↑ S. G. Charati† and, & Stern, S. A. (1998). Diffusion of gases in silicone polymers:  molecular dynamics simulations. Macromolecules, 31(16), 5529-5535.
  4. ↑ Hofmann, D., Fritz, L., Ulbrich, J., Schepers, C., & Böhning, M. (2000). Detailed‐atomistic molecular modeling of small molecule diffusion and solution processes in polymeric membrane materials. Macromolecular Theory & Simulations, 9(6), 293–327.


Made by from the elegans.Inc in SUSTech_Shenzhen.

Licensed under CC BY 4.0.

  • ©2017 SUSTech_Shenzhen